Imaging and Information Processing of Pitting-Corroded Aluminum Alloy Panels with Surface Metrology Methods

##plugins.themes.bootstrap3.article.main##

##plugins.themes.bootstrap3.article.sidebar##

Published Sep 29, 2014
Honglei Li Margaret R. Garvan Jiaming Li Javier Echauz Douglas Brown George J. Vachtsevanos

Abstract

It has been established that corrosion is one of the most important factors causing structural deterioration, loss of metal, and ultimately decrease of product performance and reliability. Corrosion monitoring, accurate detection and interpretation are recognized as key enabling technologies to reduce the impact of corrosion on the integrity of critical aircraft and industrial assets. Interest in corrosion measurement covers a broad spectrum of technical approaches including acoustic, electrical and chemical methods. Surface metrology is an alternative approach used to measure corrosive rate and material loss by obtaining surface topography measurement at micrometer levels. This paper reports results from an experimental investigation of pitting corrosion detection and interpretation on aluminum alloy panels using 3D surface metrology methods, image processing and data mining techniques. Sample panels of AA 7075-T6, an aluminum alloy commonly used in aircraft structures, were coated on one side with a corrosion- protection coating and assembled in a lap-joint configuration. Then, a series of accelerated corrosion testing of the lap-joint panels were performed in a cyclic corrosion chamber running ASTM G85-A5 salt fog test. Panel surface characterization was evaluated with laser microscopy and stylus-based profilometry to obtain global and local surface images/characterization. Promising imaging and surface features were extracted and compared between the uncoated and coated panel sides, as well as on the uncoated sides under different corrosion exposure times. In the evaluation process, image processing, information processing and other data mining techniques were utilized. Information processing involves the steps of feature or Condition Indicator extraction and selection. The latter step addresses the problem of selecting those features that are maximally correlated with the actual corrosion state, for the purpose of corrosion detection, localization, quantification and state estimation. The results, verified by mass loss data, confirmed the contention that pits at the panel surfaces formed as a result of electrochemical corrosion attack, and showed that deteriorating pitting corrosion attack correlates with increasing corrosion exposure times. This study is a first step in the process of understanding, assessing and responding to the pitting corrosion and ultimately preventing material failure to insure aircraft structural integrity.

How to Cite

Li, H. ., R. Garvan, M. ., Li, J. ., Echauz, J. ., Brown, D. ., & J. Vachtsevanos, G. (2014). Imaging and Information Processing of Pitting-Corroded Aluminum Alloy Panels with Surface Metrology Methods. Annual Conference of the PHM Society, 6(1). https://doi.org/10.36001/phmconf.2014.v6i1.2419
Abstract 259 | PDF Downloads 144

##plugins.themes.bootstrap3.article.details##

Keywords

corrosion, structural health monitoring, data mining, pitting corrosion, surface metrology, image processing, aluminum alloy

References
Belanger, P., Cawley, P. and Simonetti, F. (2010). Guided wave diffraction tomography within the Born approximation, IEEE Trans UFFC, Vol. 57, pp. 1405- 1418.

Clark, T., (2009). Guided wave health monitoring of complex structures. Doctoral dissertation. Imperial College London, London, United Kingdom.

Frankel, G. S. (1998). Pitting corrosion of metals a review of the critical factors. Journal of the Electrochemical Society, 145(6), 2186-2198.

Huang, T.-S. & Frankel, G. S. (2006). Influence of Grain Struc- ture on Anisotropic Localized Corrosion Kinetics of AA7xxx-T6 Alloys. Corrosion Engineering, Science and Technology, Vol. 41, No. 3, pp. 192-199. doi:10.1179/174327806X120739.

Li, H., Michaels, J. E., Lee, S. J., Michaels, & T. E., Thompson, D. O., & Chimenti, D. E. (2012).
Quantification of surface wetting in plate-like structures via guided waves. In AIP Conference Proceedings- American Institute of Physics, Vol. 1430, No. 1, p. 217.

Pereira, M. C., Silva, J. W., Acciari, H. A., Codaro, E. N., & Hein, L. R. (2012). Morphology Characterization and Kinetics Evaluation of Pitting Corrosion of Commercially Pure Aluminium by Digital Image Analysis. Materials Sciences & Applications, 3(5), pp. 287-293.

Rao, K. S., & Rao, K. P. (2004). Pitting Corrosion of Heat- Treatable Aluminium Alloys and Welds: A Review. Transactions of the Indian Institute of Metals, Vol. 57, No. 6, pp. 593-610.

Shell, E. B., Buchheit, R. G., & Zoofan, B. (2005). Correlation of residual fatigue life with quantified NDE measurements. International Journal of Fatigue, 27(2), 105-112.

Silva, J. W. J., Bustamante, A. G., Codaro, E. N., Na- kazato, R. Z., & Hein, L. R. O. (2004). Morphological Analysis of Pits Formed on Al 2024-T3 in Chloride Aqueous Solution. Applied Surface Science, Vol. 236, No. 1-4, pp. 356-365. doi:10.1016/j.apsusc.2004.05.007.

Szklarska-Smialowska, Z. (1999). Pitting corrosion of aluminum. Corrosion Science, 41(9), 1743-1767.

Trdan, U., Ocaña, J.L., Grum, J. (2009). Surface Evaluation of Laser Shock Processed Aluminum Alloy After Pitting Corrosion Attack with Optical 3-D Metrology Method. The 10th International Conference of the Slovenian Society for Non-Destructive Testing, September 1-3, 2009, Ljubljana, Slovenia.
Section
Technical Research Papers

Most read articles by the same author(s)