Gear Fault Location Detection for Split Torque Gearbox using AE Sensors
In comparison with a traditional planetary gearbox, the split torque gearbox (STG) potentially offers lower weight, increased reliability, and improved efficiency. These benefits have driven helicopter OEMs to develop products using STG. However, the effect of multiple gears meshing simultaneously with the central gear and a large number of synchronous components (gears or bearing) in close proximity creates a problem on how to detect the gear fault location in a STG. As of today, only limited research on STG fault detection using vibration sensors and acoustic emission sensors has been conducted.In this paper, an effective methodology on gear fault location detection using AE sensors for STG is presented. The methodology uses wavelet transform to process the AE sensor signals to determine the arrival time of the AE bursts at different locations. By analyzing the arrival times of the AE bursts, the gear fault location can be determined. The parameters of the wavelet transform are optimized by using an ant colony optimization algorithm. Real seeded gear fault experimental tests on a notational STG are conducted. AE sensor signals at the locations of healthy and damaged output driving gears are collected simultaneously to determine the location of the damaged gear. Experimental results have shown the effectiveness of the presented methodology.
How to Cite
wavelet transform, Gear fault location detection, split torque gearbox, acoustic emission, ant colony optimization
Blunt D. M. and Keller J. A., (2006), “Detection of a Fatigue Crack in a UH-60A Planet Gear Carrier Using Vibration Analysis”, Mechanical Systems and Signal Processing, Vol. 20, pp. 2095 – 2111.
Boczar T. and Zmarz D., (2004), “Application of wavelet analysis to acoustic emission pulses generated by partial discharges” IEEE Transactions on Dielectrics and Electrical Insulation, vol. 11, p. 433.
Chen D., (2002), “Classification of Wavelet Map Patterns using Multi-Layer Neural Networks for Gear Fault Detection”, Mechanical Systems and Signal Processing, Vol. 16, No. 4, pp. 695 – 704.
Couturier J. and Mba D., (2008), “Operational Bearing Parameters and Acoustic Emission Generation”, Journal of Vibration and Acoustics, Vol. 130, No. 2, pp. 024502.1 – 024502.5.
Dalpiaz G. Rivola A., and Rubini R., (2000), “Effectiveness and Sensitivity of Vibration Processing Techniques for Local Fault Detection in Gears”, Mechanical Systems and Signal Processing, Vol. 14, No. 3, pp. 387 – 412.
Eftekharnejad B. and Mba D., (2009), “Seeded Fault Detection on Helical Gears with Acoustic Emission”, Applied Acoustics, Vol. 70, pp. 547 – 555.
Elforjani M. and Mba D., (2009), “Detecting Natural Crack Initiation and Growth in Slow Speed Shafts with the Acoustic Emission Technology”, Engineering Failure Analysis, Vol. 16, pp. 2121 – 2129.
Gary J. and Hamstad M., (1994), “On the far-field structure of waves generated by a pencil lead break on a thin plate”, Journal of Acoustic Emission, vol. 12, pp. 157-170.
Ghamd A. M. and Mba D., (2006), “A Comparative Experimental Study on the Use of Acoustic Emission and Vibration Analysis for Bearing Defect Identification and Estimation of Defect Size”, Mechanical Systems and Signal Processing, Vol. 20, pp. 1537 – 1571.
Halim E. B., Choudhury M. A. A. S., Shah S. L., and Zuo M. J., (2008), “Time Domain Averaging Across All Scales: A Novel Method for Detection of Gearbox Faults”, Mechanical Systems and Signal Processing, Vol. 22, pp. 261 – 278.
Hamzah R. I. R. and Mba D., (2009), “The Influence of Operating Condition on Acoustic Emission Generation During Meshing of Helical and Spur Gear”, Tribology International, Vol. 42, pp. 3 – 14.
Hanchi J. and Kiamichi B. E., (1990), “Acoustic Emission Monitoring of the Wear Process”, Wear, Vol. 145, pp. 1 – 27.
He Y. Y, Yin X. Y, and Chu F. L., (2008), “Modal Analysis of Rubbing Acoustic Emission for Rotor- Bearing System Based on Reassigned Wavelet Scalorgram”, Journal of Vibration and Acoustics, Vol. 130, pp. 061009.1 – 061009.8.
Jeong H. and Jang Y. S., 2000, “Fracture Source Location in Thin Plates Using the Wavelet Transform of Dispersive Waves”, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control. Vol. 47, No. 3, pp. 612 – 619.
Lee D. E, Hwang I, Valente C. M. O., Oliveira J. F. G, and Dornfeld D. A., (2006), “Precision Manufacturing Process monitoring with Acoustic Emission”, International Journal of Machine Tools and Manufacture, Vol. 46, No. 2, pp. 176 – 188.
Leguizamon G., Michalewicz Z., and Schutz M., (2001), “An Ant System for the Maximum Independent Set Problem”, Proceedings of the 2001 Argentinian Congress on Computer Science, Vol. 2, pp. 1027 – 1040.
Li R. Y., He D., and Bechhoefer E., (2009), “Gear Fault Detection for the Split Torque Transmission System Using Acoustic Emission and Vibration Signals”, Annual Conference of the Prognostics and Health Management Society 2009, San Diego, CA.
Li X. L., (2002), “A Brief Review: Acoustic Emission Method for Tool Wear Monitoring During Turning”, International Journal of Machine Tools and Manufacture, Vol. 42, pp. 157 – 165.
Liu B., Riemenschneider S., and Xu Y., (2006), “Gearbox Fault Diagnosis Using Empirical Mode Decomposition and Hilbert Spectrum”, Mechanical Systems and Signal Processing, Vol. 20, pp. 718 –734.
Martens D., Backer M., Haesen R., Vanthienen J.,Snoeck M., and Baesens B., (2007), “Classification with Ant Colony Optimization”, IEEE Transactions on Evolutionary Computation, Vol. 11, No. 5, pp. 651 – 665.
McFadden P. D., (2000), “Detection of Gear Faults by Decomposition of Matched Differences of Vibration Signals”, Mechanical Systems and Signal Processing, Vol. 14, No. 5, pp. 805 – 817.
McFadden. P. D., (1987), “A Revised Model for the Extraction of Periodic Waveforms by Time Domain Averaging”, Mechanical Systems and Signal Processing, Vol. 1, No. 1, pp. 83 – 95.
Naim B. and Andrew B., (2001), “A Comparative Study of Acoustic and Vibration Signals in Detection of Gear Failures Using Wigner-Ville Distribution”, Mechanical Systems and Signal Processing, Vol. 15, No. 6, pp. 1091 – 1107.
Nivesrangsan P., Steel J. A., and Reuben R. L., (2005), “AE Mapping of Engines for Spatially Located Time Series”, Mechanical Systems and Signal Processing, Vol. 21, No. 2, pp. 1084 – 1102.
Seckiner S.U. and Kurt M., (2008), “Ant Colony Optimization for the Job Rotation Scheduling Problem”, Applied Mathematics and Computation, Vol. 201, pp. 149 -160.
Secomandi N., (2004), “Comparing Neuro-Dynamic Programming Algorithms for the Vehicle Routing Problem with Stochastic Demands”, Computers & Operation Research, Vol. 27, No. 11, pp. 1201 – 1225.
Stützle, T. and Dorigo, M. (1999) “ACO algorithms for the traveling salesman problem”, in K. Miettinen, M. Makela, P. Neittaanmaki and J. Periaux (Eds.) Evolutionary Algorithms in Engineering and Computer Science: Recent Advances in Genetic Algorithms, Evolution Strategies, Evolutionary Programming, Genetic Programming and Industrial Applications, John Wiley & Sons.
Toksari M. D., (2006) “Ant Colony optimization for finding the global minimum”, Applied Mathematics and Computation, Vol. 176, pp. 308-316.
Toutountzakis T., Tan C. K., and Mba D., (2005), “Application of Acoustic Emission to Seeded Gear Fault Detection”, NDT&E International, Vol. 38, pp. 27 -36.
White G., (1982), “Split Torque Transmission”, USPTO, 4,489,625, 1982.
The Prognostic and Health Management Society advocates open-access to scientific data and uses a Creative Commons license for publishing and distributing any papers. A Creative Commons license does not relinquish the author’s copyright; rather it allows them to share some of their rights with any member of the public under certain conditions whilst enjoying full legal protection. By submitting an article to the International Conference of the Prognostics and Health Management Society, the authors agree to be bound by the associated terms and conditions including the following:
As the author, you retain the copyright to your Work. By submitting your Work, you are granting anybody the right to copy, distribute and transmit your Work and to adapt your Work with proper attribution under the terms of the Creative Commons Attribution 3.0 United States license. You assign rights to the Prognostics and Health Management Society to publish and disseminate your Work through electronic and print media if it is accepted for publication. A license note citing the Creative Commons Attribution 3.0 United States License as shown below needs to be placed in the footnote on the first page of the article.
First Author et al. This is an open-access article distributed under the terms of the Creative Commons Attribution 3.0 United States License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.