Cure Monitoring of Composite Carbon/Epoxy through Electrical Impedance Analysis

##plugins.themes.bootstrap3.article.main##

##plugins.themes.bootstrap3.article.sidebar##

Published Jul 8, 2014
M. Mounkaila T. Camps S. Sassi Ph. Marguerès Ph. Olivier J.Y. Fourniols C. Escriba

Abstract

Composite materials are increasingly used in aeronautic; they offer many benefits such as mechanical strength, mass and consumption reduction. However, their process development needs to be known and controlled, in order to adjust the process parameters and optimize the characteristics of structures made from these materials. This paper is focused on impedance spectroscopy measurement and analysis technique to characterize material’s properties. In fact, the composites based on carbon fiber have electrical proprieties; therefore a three-dimensional modeling of the electrical conduction in the material is established by using a distributed allocation of an electrical resistance (RP) in parallel with a capacitance (CP). Then, thin electrodes (40 μm thick) are inserted inside the material and a specific impedance measurement bench is developed to perform real-time measurements of RP and CP on unidirectional (UD) mono-ply and multi-plies samples. During curing (in an oven) the change in values of both RP and CP in different stages of the curing cycle is showed. Then, problems that occur during the curing cycle (layup defect, loss of vacuum) were detected by a large gap of the measured electrical parameters in comparison with the ordinary case. Therefore, by this electrical measurement, we present a way to ensure an automated real-time monitoring of the composite curing process.

How to Cite

Mounkaila, M., Camps, T., Sassi, S., Marguerès, P., Olivier, P., Fourniols, J., & Escriba, C. (2014). Cure Monitoring of Composite Carbon/Epoxy through Electrical Impedance Analysis. PHM Society European Conference, 2(1). https://doi.org/10.36001/phme.2014.v2i1.1504
Abstract 423 | PDF Downloads 129

##plugins.themes.bootstrap3.article.details##

Keywords

CFRP, Electrical modeling, Electrical impedance spectroscopy, cure monitoring

References
Ryan, M., Carolyn, P., & Karim, Y. (2002), Insulation Cure Monitoring on Global VPI Large AC Motors. Proceedings of IEEE Symposium on Electrical Insulation, April 7- 10, Boston, MA USA.
doi:10.1109/ELINSL.2002.995982
Inada, T., & Todoroki, A. (2005). Smart Cure Monitoring Method of Carbon/Epoxy Laminates using Electric Capacitance Change with Applied Alternating Current Frequency. Key Engineering Materials, Vols. 297-300, pp. 2903 - 2908. dio: 10.4028/www.scientific.net/KEM.297-300.2903
Shoukai, W., & Chung, D.D.L. (1999). Apparent negative electrical resistance in carbon fiber composites. Composites, Part B 30, pp. 579 - 590. dio: 10.1016/S1359-8368(99)00021-9
Joung-Man, P., Sang-Il, L., & Jin-Ho, C. (2005). Cure monitoring and residual stress sensing of single-carbon fiber reinforced epoxy composites using electrical resistivity measurement. Composites Science and Technology, Vol. 65, pp. 571–580. doi:10.1016/j.compscitech.2004.09.019
Marguerès, P., Camps, T., Viargues, M., & Olivier, P. (2013). Preliminary experimental study on the electrical impedance analysis for in-situ monitoring of the curing of carbon/epoxy composite material for aeronautical and aerospace structures. Meas. Sci. Technol, Vol. 24, 095005 (10pp). doi:10.1088/0957-0233/24/9/095005
Section
Technical Papers

Similar Articles

<< < 5 6 7 8 9 10 11 12 13 14 > >> 

You may also start an advanced similarity search for this article.